Changes

Deciding whether or not to boil the wort can also depend on whether or not there was a considerable amount of alcohol produced, which commonly happens when the wort is contaminated with yeast. Pure cultures of ''Lactobacillus'' do not show typical signs of fermentation that we are used to seeing with yeast fermentations, such as forming a krausen, producing a lot of CO2, or fermenting wort more than ~1.005 gravity points (see [[100% Lactobacillus Fermentation]]). If a yeast contamination produces a significant amount of alcohol during the souring process, then this presents a problem when it comes to boiling. Although 100% pure ethanol boils at 173.1°F/78.4°C <ref name="boiling_of_alcohol">[http://chemistry.about.com/od/moleculecompoundfacts/f/What-Is-The-Boiling-Point-Of-Alcohol.htm Boiling temperature of ethanol]</ref>, the lower the concentration of ethanol in the wort (technically beer at this point if it has been fully attenuated by yeast), the higher the temperature required for boiling off the ethanol. For example, at 5% ABV it takes approximately 197°F/92°C for the ethanol to boil <ref>[http://www.clawhammersupply.com/blogs/moonshine-still-blog/12243869-making-moonshine-still-temperature Making Moonshine: Still Temperature. Retrieved 01/11/2016.]</ref><ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1212116758816536/?comment_id=1212140998814112&comment_tracking=%7B%22tn%22%3A%22R%22%7D Conversation with Russell Carpenter on MTF. 01/11/2016.]</ref>. Time is also required to boil off the ethanol, so this may not be as big of a concern as it first appears (''warning: vaporized ethanol is highly flammable)''. Another and perhaps more important consideration is that boiling and high heat pasteurization temperatures can have a negative effect on the flavor of fermented beer. Beer already has anti-bacterial properties, such as low pH, presence of alcohol, and hops (although hops may not be present in wort being soured), so higher pasteurization temperatures aren't necessarily required for beer. For these reasons, the beer industry commonly heat pasteurizes beer at 140°F/60°C for 15 minutes, and this is also adequate for pasteurizing soured beer wort that accidentally fermented do to yeast contamination <ref>[http://www.sciencedirect.com/science/article/pii/S0023643806002854#bib16 A suitable model of microbial survival curves for beer pasteurization. Sencer Buzrul. 2006.]</ref>. In Although the case of an accidental yeast contamination will be killed during the souring processpasteurization, so will the ''Lactobacillus'', another option is and the brewer can trust that equipment downstream shouldn't get contaminated. Other options are to simply dump the batch and start again with a pure culture of ''Lactobacillus'', or do not pasteurize and let the ''Lactobacillus'' live. If the ''Lactobacillus'' is not pasteurized and allowed to live, the soured wort/beer should be treated with care so that it does not contaminate the rest of the brewery (see [[FAQ#Do_I_need_separate_equipment|'Do I need Separate Equipment?' FAQ]]).  Boiling soured wort that hasn't had an accidental yeast contamination (and thus still has a high specific gravity) probably has less of an effect on the flavor than it does on fully fermented beer. Other than lactic acid, the flavor components that different strains of ''Lactobacillus'' produce are not well defined, so it will be difficult to determine if boiling soured wort will have a negative impact. However, brewers who boil kettle soured wort don't often report that the boiling causes flavor issues <ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1464590560235820/?comment_id=1465040723524137&reply_comment_id=1465146946846848&comment_tracking=%7B%22tn%22%3A%22R4%22%7D Conversation with Bryan from Sui Generis blog on MTF regarding boiling soured wort. 11/10/2016.]</ref>.