|
|
| (85 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | '''Sour Worting''' is a process in which ''[[Lactobacillus]]'' is given a "head start", pitched before the yeast so that it will be able to produce significant amounts of lactic acid before the ''Saccharomyces'' completes the main fermentation. There are several variations on this method, including souring in the primary fermenter, souring in a secondary vessel, or even souring in the boil kettle itself. There are also various methods of inoculating the wort with ''Lactobacillus''. Finally, the brewer has the option of pasteurizing the wort by heating it to kill the ''Lactobacillus'' before adding the yeast for the main fermentation. Many brewers prefer this process over [[Sour Mashing]] because it can be easier to control, and when implemented properly it produces a clean sour beer in a short amount of time. The possibility of pasteurizing the soured wort also makes this a good method for making sour beers with a lot of residual malt sweetness (e.g. sour barley wines), and should also make it attractive to brewers who are concerned about infection issues in their cold side equipment (equipment that is used post-boil) <ref>[http://sourbeerblog.com/fast-souring-lactobacillus/ Miller, Matt. Dec 20, 2014. "Fast Souring with ''Lactobacillus'' – Best Practices, Sensory, & Science". Sour Beer Blog.]</ref>. When sour worting, some brewers first [[Sour_Worting#How_to_Pre-Acidify|lower the pH of the wort to 4.5-4.8]] before pitching ''Lactobacillus''. This has sometimes been found to help the head retention of the beer. For more information, see the [[Lactobacillus#Foam_Degradation|''Lactobacillus'' page section on Foam Degradation]].
| + | #REDIRECT [[Wort_Souring]] |
| − | | |
| − | Important note regarding aluminum pots: souring in an aluminum vessel may strip the aluminum of the protective oxide layer. The oxide layer is only stable at a pH of 4.5 - 8.5. Therefore, kettle souring in an aluminum pot is generally not recommended <ref>[http://www.pfonline.com/articles/aluminum-surface-finishing-corrosion-causes-and-troubleshooting Aluminum Surface Finishing Corrosion Causes and Troubleshooting. W. John Fullen, Boeing Research and Technology & Jennifer Deheck, Boeing, Seattle, Washington, USA. 10/17/2014.]</ref>.
| |
| − | | |
| − | <blockquote>"''Mixed culture fermentation for sour beers produces one thing, and (kettle souring) produces another thing. If you’re going to make a malty red ale that is kettle soured, don’t call it a Flanders Red. Honor the tradition.''" - Sean Burke of the Commons Brewery, Kettle Souring Presentation, CBC 2015.</blockquote>
| |
| − | | |
| − | ==Processes==
| |
| − | | |
| − | ===Souring in the Boil Kettle===
| |
| − | Also known as "kettle souring", souring in the boil kettle is a simple process that is often used if the brewer wants to subsequently heat pasteurize the wort. Pasteurizing the wort has the advantage of allowing the brewer to rack the pasteurized wort into a fermenter and pitch brewer's yeast without fear of an ongoing ''Lactobacillus'' infection in their post-boil equipment.
| |
| − | | |
| − | The brewing process is the same for any all grain batch up until the first wort and sparge runnings are collected into the boil kettle. The temperatures that a typical mash out/sparge reach should be enough to pasteurize the wort <ref name="pasteurization">[http://science.howstuffworks.com/life/cellular-microscopic/pasteurization4.htm Heat pasteurization]</ref>, however we advise heating the wort for a short (1-2 minutes) boil in order to kill a greater degree (2-3 logs more) of thermotolerant microbes <ref name="Heit_boiling">[https://www.facebook.com/groups/MilkTheFunk/permalink/1180630378631841/?comment_id=1180634488631430&reply_comment_id=1180677581960454&comment_tracking=%7B%22tn%22%3A%22R2%22%7D Conversation with Bryan of Sui Generis Blog regarding boiling versus lower temperature pasteurization. 11/18/2015.]</ref><ref>[http://sourbeerblog.com/lactobacillus-2-0-advanced-techniques-for-fast-souring-beer/ ''Lactobacillus'' 2.0 – Advanced Techniques for Fast Souring Beer. 11/18/2015. Retrieved 11/19/2015.]</ref>. Once all of the wort is collected in the boil kettle (and preferably brought to a boil), the wort is chilled to around 80-120°F (37-48°C), depending on the ''[[Lactobacillus]]'' culture that is being used. Once chilled to the temperature that is appropriate, the wort in the kettle is inoculated with a culture of ''Lactobacillus''.
| |
| − | | |
| − | There are various ways of inoculating the wort. A reliable method is pitching a pure culture of ''Lactobacillus'', or a blend of ''Lactobacillus'' cultures. Alternatively, a handful of unmilled malted barley can be added to the kettle for inoculation instead of a pure culture, since the husks of grain carry many microorganisms. If unmilled grain is added, it is recommended to fill the head space of the kettle with CO2 because oxygen can encourage off flavors such as rancid cheese from [[Butyric Acid]] and/or [[Isovaleric Acid]], which are produced by microbes that are naturally present on the grain. Keeping the temperature between 113-120°F (45-48.8°C) will encourage the ''Lactobacillus'' resident on the grain and will discourage other bacteria. Lowering the pH of the [[Sour_Worting#How_to_Pre-Acidify|wort to 4.5]] will also discourage many other bacteria from thriving in the wort during the incubation period. Consider [[Alternative Bacteria Sources]] for more reliable approaches to using "wild" ''Lactobacillus'', or ''Lactobacillus'' from sources other than yeast labs.
| |
| − | | |
| − | If a pure culture of ''Lactobacillus'' bacteria is used it is ideal but not necessary to fill the head space of the fermenter with CO2 gas (some brewers have reported that this will help reduce sulfur in the finished beer). The kettle should be held at the desired temperature for 24-72 hours (in some cases longer, but no longer than 5 days). Depending on the strain of ''Lactobacillus'', and the desired sour level, the time of incubation is ultimately a variable that is up to the brewer (see the ''[[Lactobacillus]]'' page for suggested temperatures and times for specific strains). The kettle lid should be firmly in place and optionally sealed with plastic wrap so that other microorganisms do not get in. Potential for formation of [[Butyric Acid]] and [[Isovaleric Acid]] when using only a pure culture is extremely slight to none assuming no other microbes are allowed inside the kettle.
| |
| − | | |
| − | Once the level of acidity is reached (this can be tested with a reliable pH meter, or in the case of using a pure culture can safely be taste tested), the wort is brought to a boil. ''Caution: the wort gravity may also be tested to check for alcohol presence. Alcohol can be more easily boiled off since it boils at 173.1°F or 78.4°C <ref name="boiling_of_alcohol">[http://chemistry.about.com/od/moleculecompoundfacts/f/What-Is-The-Boiling-Point-Of-Alcohol.htm Boiling temperature of ethanol]</ref>.'' The wort may be boiled normally in the case of any style of beer that requires a longer boiling process, or it it may be boiled for no more than a minute or two in the case of making a [[Berliner Weissbier]]. Technically speaking, the wort doesn't need to be boiled at all (this is called [http://www.garshol.priv.no/blog/331.html Raw Ale]). Heat pasteurization should kill the ''Lactobacillus'' culture being used to sour the wort <ref name="pasteurization" />, so if alcohol is present then the brewer can choose to heat pasteurize the wort at 170°F (76.6°C) for 15 minutes.
| |
| − | | |
| − | Once the soured wort is boiled or heat pasteurized, it can be safely added to the primary fermenting vessel without worries of future infections. The wort is aerated as normal, and brewer's yeast, or ''[[Brettanomyces]]'' yeast is then pitched into the wort as normal (usually brewer's yeast is used if infection of cold side equipment is a concern). At a pH of 3.4 or lower, the acidity of the wort can reportedly effect the fermentation of some strains of brewer's yeast <ref name="low ph">[http://www.homebrewtalk.com/f127/no-hop-berliner-weisse-415067/index3.html#post5280971 Michael Tonsmeire on HBT]</ref>. It is recommended to pitch a healthy starter of yeast, possibly with a higher cell count than normal. In the case of using dry yeast, re-hydrating as per the manufacturer's recommendations and using a yeast nutrient like Go-Ferm is recommended. Many yeast strains have been successfully used by MTF members to ferment pre-acidified wort: US05, S04, WY1098/WLP007/OYL-006, Belle Saison, Sacch Trois, Bret brux, B. clausenii, B. custersianus, Bret Drie (BSI), WY3711, and WY3726 to name a few (see reference) <ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1105185972842949/ Conversation on MTF about using specific yeast strains in acidic wort. 7/6/2015.]</ref>.
| |
| − | | |
| − | ===Souring in the Primary Fermenter===
| |
| − | | |
| − | Wort can be soured in the primary fermenter before adding other yeasts. This is generally a good approach for brewers who aren't concerned with pasteurization and infections of their cold side equipment. This has the advantage of possibly producing a more complex sour beer overall, or at least a sour beer that will evolve over time. It has the advantage over a more traditional [[Mixed Fermentation]] in that ''Lactobacillus'' is used to guarantee at least a certain level of sourness. This is also a good process to use for making a [[Berliner Weissbier]].
| |
| − | | |
| − | The process is very similar to the sour worting technique, except the wort is never pasteurized after it is soured. The all grain brewing process is the same for any all grain brewing process, except that after the boil the beer is only chilled to the recommended temperature for the ''Lactobacillus'' strain that the brewer is going to use. Using grain husks for souring with this method is not advised since the grain will stay in the fermenter during primary fermentation, and unwanted microbes on the grain husks would potentially have a longer exposure to the wort. Instead, the brewer should use a pure strain of ''[[Lactobacillus]]''. As a result of not using grains to sour the wort, there is little concern of developing [[Butyric Acid]] or [[Isovaleric Acid]] with this method. There is also the option of [[Mixed_Fermentation#Reusing_a_Sour_Yeast_Cake|using a sour yeast cake]] from another sour beer as the bacteria inoculation.
| |
| − | | |
| − | Once cooled to the desired temperature (usually around 90-120°F or 32.2-48.8°C), the wort is racked to the primary fermenting vessel. Note that the wort should contain a low amount of IBU's when using this process since IBU's can inhibit many (but not all) species of ''[[Lactobacillus]]''. Using no hops is a good approach to getting more acidity, but if hops are required then using less than 6 IBU's is a good guideline in general (consider mash hopping; mash hopping has been reported to reduce IBU's by ~70% <ref>[http://www.homebrewersassociation.org/how-to-brew/resources/conference-seminars/ ''Putting Some Numbers on First Wort and Mash Hop Additions''. David Curtis NHC 2014 Presentation.]</ref>). It may or may not be advised to create a ''Lactobacillus'' starter (see the ''[[Lactobacillus]]'' page) before hand. Once the wort is racked to the primary fermenting vessel, the ''Lactobacillus'' culture is added directly to the fermenter. No other yeasts are added at this time. The ''Lactobacillus'' bacteria is allowed to incubate by itself in the wort for 2-5 days with the before mentioned target temperature maintained throughout the incubation period (some ''Lactobacillus'' species/strains may continue to produce acidity under lower temperatures). The exact time frame of incubation depends on the species/strain of ''Lactobacillus'', the manufacturer's recommendation, and the brewer's desired acidity level. Acidity can safely be measured with a reliable pH Meter throughout this time. If possible, it is advised that the brewer fill the head space of the fermenter with CO2. Some brewers have reported that this helps to reduce sulfur production, but if ''Brettanomyces'' is added to the beer later on in the process and allowed to age, this shouldn't be a concern.
| |
| − | | |
| − | After the desired acidity level is reached from the incubating ''Lactobacillus'' bacteria, the brewer can crash cool the fermenter down to the temperature that is desired for the primary fermenting yeast. Both ''[[Saccharomyces]]'' and ''[[Brettanomyces]]'', or a blend can be used as primary fermenting yeast. ''Brettanomyces'' is often chosen because of it's higher tolerance of a low pH environment (3.4- pH <ref name="low ph">[http://www.homebrewtalk.com/f127/no-hop-berliner-weisse-415067/index3.html#post5280971 Michael Tonsmeire on HBT]</ref>), although many ''Saccharomyces'' strains have been successfully used (see the ''Souring in the Boil Kettle'' section above). If the chosen yeast requires aeration and the brewer has the ability, the sour wort should be aerated before pitching yeast. Brewers have had good luck using Fermentis dry yeast products in non-aerated wort. Re-hydrating the dry yeast as per the manufacturer's instructions and with a yeast nutrient such as Go-Ferm is effective <ref>[http://www.scottlab.com/product-102.aspx Go-Ferm]</ref>. The wort is then fermented out as normal. The brewer can consider other [[Brewing Methods]] such as pitching ''Brettanomyces'', a mixed culture, or commercial sour beer dregs into secondary.
| |
| − | | |
| − | ===Souring in Another Vessel Before Racking to the Primary Fermenter===
| |
| − | This process is very similar to sour worting in the kettle. This method is ideal for those who wish to use grains to introduce ''Lactobacillus'' to the beer. If done properly, the formation of [[Butyric Acid]] and [[Isovaleric Acid]] should be minimal.
| |
| − | | |
| − | The wort is mashed and sparged as normal (and alternatively brought to a short boil), and is then lowered to somewhere between 113-120°F (45-48.8°C). This temperature favors ''Lactobacillus'', while discouraging Enterobacteriaceae. Optionally, the mash pH can be lowered to 4.4 with lactic acid or acidulated malt to further discourage Enterobacteriaceae activity. Once the desired temperature (and optionally pH) is reached, a handful of fresh malted unmilled grain is added to the mash and allowed a few minutes to inoculate the mash with the microbes found naturally on the grain husks. The wort is then transferred to a second vessel such as a glass carboy. The vessel should be filled to the very top, minimizing the oxygen levels inside the vessel. The vessel should be stored in a heated environment that maintains a temperature between 113-120°F (45-48.8°C) for 1 to 4 days depending on how much acidity the brewer wants (3 days is a good rule of thumb) <ref name="james_spencer">[http://beerandwinejournal.com/sour-wort-berliner/ Spencer, James. December 15, 2014. Beer and Wine Journal.] </ref>.
| |
| − | | |
| − | Once the 1 to 4 day time period has been reached, the wort is transferred to the boil kettle and boiled as normal. Boiling will kill all of the microorganisms in the wort, and will provide the option for adding hops and other kettle additions. Just as with kettle souring, the wort doesn't have to be boiled, but can be instead heat pasteurized at 170°F (76.6°C) for 15 minutes <ref name="pasteurization" />. ''Caution: the wort gravity may also be tested to check for alcohol presence. Alcohol can be more easily boiled off since it boils at 173.1°F (78.37°C) <ref name="boiling_of_alcohol" />.'' Once boiled, the wort can be chilled and handled in the same way as the above methods for wort souring.
| |
| − | | |
| − | [http://beerandwinejournal.com/sour-wort-berliner/ James Spencer provides an article] that fully explains his process, as well as a step by step video guide and tasting on Beer and Wine Journal <ref name="james_spencer" />.
| |
| − | | |
| − | ===How to Pre-Acidify===
| |
| − | After the production of the wort, but before pitching the culture of ''Lactobacillus'', some brewers like to slightly lower the pH of the wort with food grade lactic acid (available at homebrew stores) or phosphoric acid before adding the ''Lactobacillus''. This has several benefits, such as discouraging unwanted microbes that may have accidentally been introduced into the wort, and helping to prevent [[Lactobacillus#Foam_Degradation|''Lactobacillus'' foam degradation]]. The idea is to get the wort down to a pH of 4.5-4.8 before adding ''Lactobacillus''. There currently is no formula for how much lactic acid to add to a volume of wort due to the different buffering capacities of wort <ref>[http://www.mbaa.com/districts/Northwest/Events/Documents/Study%20in%20the%20Practical%20Use%20of%20Lactic%20Acid%20Bacteria.pdf A Study in the Practical Use of Lactic Acid Bacteria. Greg Doss from Wyeast Laboratories Inc. 2014.]</ref>, but using 1 mL of 88% lactic acid per .1 shift in pH for 5 gallons of wort is a good starting measurement. As an example, say that 5 gallons of wort has a pH of 5.0 just before pitching the ''Lacto''. Begin by adding 5 mL of food grade lactic acid to the wort for a target of 4.5 pH. Stir gently, then take another pH reading. Continue to add 1-2 mL of lactic acid until the wort has the desired pH. Once the desired pH is reached, pitch the ''Lacto'' culture. This small amount of lactic acid shouldn't have a much of an overall flavor impact.
| |
| − | | |
| − | ==See Also==
| |
| − | ===Additional Articles on MTF Wiki===
| |
| − | * [[Sour Mashing]]
| |
| − | * [[Alternative Bacteria Sources]]
| |
| − | * ''[[Lactobacillus]]''
| |
| − | * [[Mixed Fermentation]]
| |
| − | | |
| − | ===External Resources===
| |
| − | * [http://suigenerisbrewing.blogspot.com/2015/07/how-i-sour-mash-recipe.html "How I Sour Mash & A Recipe"; Sui Generis Blog (includes Sour Worting and microbiology information).]
| |
| − | * [http://www.fivebladesbrewing.com/year-sour-mash/ "Year of the Sour Mash" by Derek Springer. This series of articles were written for his NHC 2015 presentation.]
| |
| − | * [http://sourbeerblog.com/lactobacillus-2-0-advanced-techniques-for-fast-souring-beer/ "Lactobacillus 2.0 - Advanced Techniques for Fast Souring Beer", by Matt Miller of Sour Beer Blog.]
| |
| − | | |
| − | ==References==
| |
| − | <references/>
| |
| − | | |
| − | [[Category:Techniques]] | |