Changes

Also known as '''kettle souring''', souring in the boil kettle is a simple process that is often used if the brewer wants to subsequently heat pasteurize the wort. Pasteurizing the wort has the advantage of allowing the brewer to rack the pasteurized wort into a fermenter and pitch brewer's yeast without fear of an ongoing ''Lactobacillus'' infection in their post-boil equipment.

There are various ways of inoculating the wort. A reliable method is pitching a pure culture of ''Lactobacillus'', or a blend of ''Lactobacillus'' cultures. Alternatively, a handful of unmilled malted barley can be added to the kettle for inoculation instead of a pure culture, since the husks of grain carry many microorganisms. If unmilled grain is added, it is thought that filling the head space of the kettle with CO2 will help decrease off-flavors such as "footiness" from [[Isovaleric Acid]], which are produced by aerobic microbes that are naturally present on the grain <ref name="khris_johnson">Personal correspondence with Khristopher Johnson of Green Bench Brewing Co. and Dan Pixley. 05/24/2016.</ref>. Keeping the temperature between 109-115°F (42.8-46°C) will encourage the ''Lactobacillus'' resident on the grain and will discourage other bacteria. Temperature consistency is critical during this process <ref name="young_grains">[https://www.facebook.com/groups/MilkTheFunk/permalink/1356058381089039/?comment_id=1356464531048424&comment_tracking=%7B%22tn%22%3A%22R%22%7D Conversation with Jeff Young from Blue Owl Brewing Co on souring from grains. 07/21/2016.]</ref>. Lowering the pH of the [[Wort_Souring#How_to_Pre-Acidify|wort to under 4.5 (ideally 4.0 - 4.3)]] will also discourage many other bacteria from thriving in the wort during the incubation period. This will also help with head retention <ref>[[Lactobacillus#Foam_Degradation]]</ref>. Souring with grains should occur within 1 or 2 days if done correctly <ref name="young_grains"></ref>. Consider [[Alternative Bacteria Sources]] for more reliable approaches to using "wild" ''Lactobacillus'', or ''Lactobacillus'' from sources other than yeast labs.

If a pure culture of ''Lactobacillus'' bacteria is used it is ideal but not necessary to fill the head space of the fermenter with CO2 gas (some brewers have reported that this will help reduce sulfur in the finished beer). Keeping positive pressure in the kettle with CO2 will help prevent contaminates that create [[Butyric Acid|butyric acid]] and other off-flavors from entering the kettle due to negative pressure, and is often the approach that commercial brewers take <ref>Personal correspondence with Steph Cope of CraftHaus Brewing Co. 02/06/2016.</ref>. The kettle should be held at the desired temperature for 24-72 hours (in some cases longer, but no longer than 5 days). Depending on the strain of ''Lactobacillus'', and the desired sour level, the time of incubation is ultimately a variable that is up to the brewer (see the ''[[Lactobacillus]]'' page for suggested temperatures and times for specific strains). The kettle lid should be firmly in place and optionally sealed with plastic wrap so that other microorganisms do not get in. Potential for formation of [[Butyric Acid]] and [[Isovaleric Acid]] when using only a pure culture is extremely slight to none assuming contamination does not occur.

Deciding whether or not to boil the wort can also depend on whether or not there was a considerable amount of alcohol produced, which commonly happens when the wort is contaminated with yeast. Pure cultures of ''Lactobacillus'' do not show typical signs of fermentation that we are used to seeing with yeast fermentations, such as forming a krausen, producing a lot of CO2, or fermenting wort more than ~1.005 gravity points (see [[100% Lactobacillus Fermentation]]). See [[Wort_Souring#Dealing_With_Yeast_Contamination|Dealing With Yeast Contamination]] below.

The wort is mashed and sparged as normal (and alternatively brought to a short boil), and is then lowered to somewhere between 109-115°F (42.8-46°C). This temperature favors ''Lactobacillus'', while discouraging Enterobacteriaceae. Optionally, the mash pH can be lowered to 4.4 with lactic acid or acidulated malt to further discourage Enterobacteriaceae activity. Once the desired temperature (and optionally pH) is reached, a handful of fresh malted unmilled grain is added to the mash and allowed a few minutes to inoculate the mash with the microbes found naturally on the grain husks. The wort is then transferred to a second vessel such as a glass carboy. The vessel should be filled to the very top, minimizing the oxygen levels inside the vessel. The vessel should be stored in a heated environment that maintains a temperature between 109-115°F (42.8-46°C) for 1 to 3 days depending on how much acidity the brewer wants (the faster the souring process the better; Jeff Young from Blue Owl achieves the desired acidity in about 18 hours usually) <ref name="young_grains"></ref><ref name="james_spencer">[http://beerandwinejournal.com/sour-wort-berliner/ Spencer, James. December 15, 2014. Beer and Wine Journal.] </ref>.

[http://beerandwinejournal.com/sour-wort-berliner/ James Spencer provides an article] that fully explains his process, as well as a step by step video guide and tasting on Beer and Wine Journal <ref name="james_spencer" />.