13,701
edits
Changes
m
adjusting recommended temps from 120 to 115 on top end
Also known as '''kettle souring''', souring in the boil kettle is a simple process that is often used if the brewer wants to subsequently heat pasteurize the wort. Pasteurizing the wort has the advantage of allowing the brewer to rack the pasteurized wort into a fermenter and pitch brewer's yeast without fear of an ongoing ''Lactobacillus'' infection in their post-boil equipment.
The brewing process is the same for any all grain batch up until the first wort and sparge runnings are collected into the boil kettle. The temperatures that a typical mash out/sparge reach should be enough to pasteurize the wort <ref name="pasteurization">[http://science.howstuffworks.com/life/cellular-microscopic/pasteurization4.htm Heat pasteurization]</ref>, however we advise heating the wort for a short (1-2 minutes) boil in order to kill a greater degree (2-3 logs more) of thermotolerant microbes <ref name="Heit_boiling">[https://www.facebook.com/groups/MilkTheFunk/permalink/1180630378631841/?comment_id=1180634488631430&reply_comment_id=1180677581960454&comment_tracking=%7B%22tn%22%3A%22R2%22%7D Conversation with Bryan of Sui Generis Blog regarding boiling versus lower temperature pasteurization. 11/18/2015.]</ref><ref>[http://sourbeerblog.com/lactobacillus-2-0-advanced-techniques-for-fast-souring-beer/ ''Lactobacillus'' 2.0 – Advanced Techniques for Fast Souring Beer. 11/18/2015. Retrieved 11/19/2015.]</ref>. Once all of the wort is collected in the boil kettle (and preferably brought to a boil), the wort is chilled to around 80-120°F 115°F (37-48°C46°C), depending on the ''[[Lactobacillus]]'' culture that is being used. Once chilled to the temperature that is appropriate, the wort in the kettle is inoculated with a culture of ''Lactobacillus''. Hops should not be added at any point before inoculating the wort with a culture of ''Lactobacillus''; most species of ''Lactobacillus'' will be inhibited by the presence of even very small amounts hops (1-2 IBU or even just hop material from dry hopping). When using a pure culture of ''Lactobacillus'', it is generally a good idea to [[Lactobacillus#Starters_and_Pitching_Rate|create a 500 mL starter]] for ~5-6 gallons of wort.
There are various ways of inoculating the wort. A reliable method is pitching a pure culture of ''Lactobacillus'', or a blend of ''Lactobacillus'' cultures. Alternatively, a handful of unmilled malted barley can be added to the kettle for inoculation instead of a pure culture, since the husks of grain carry many microorganisms. If unmilled grain is added, it is thought that filling the head space of the kettle with CO2 will help decrease off-flavors such as "footiness" from [[Isovaleric Acid]], which are produced by aerobic microbes that are naturally present on the grain <ref name="khris_johnson">Personal correspondence with Khristopher Johnson of Green Bench Brewing Co. and Dan Pixley. 05/24/2016.</ref>. Keeping the temperature between 109-115°F (42.8-46°C) will encourage the ''Lactobacillus'' resident on the grain and will discourage other bacteria. Temperature consistency is critical during this process <ref name="young_grains">[https://www.facebook.com/groups/MilkTheFunk/permalink/1356058381089039/?comment_id=1356464531048424&comment_tracking=%7B%22tn%22%3A%22R%22%7D Conversation with Jeff Young from Blue Owl Brewing Co on souring from grains. 07/21/2016.]</ref>. Lowering the pH of the [[Sour_Worting#How_to_Pre-Acidify|wort to under 4.5 (ideally 4.0 - 4.3)]] will also discourage many other bacteria from thriving in the wort during the incubation period. This will also help with head retention <ref>[[Lactobacillus#Foam_Degradation]]</ref>. Souring with grains should occur within 1 or 2 days if done correctly <ref name="young_grains"></ref>. Consider [[Alternative Bacteria Sources]] for more reliable approaches to using "wild" ''Lactobacillus'', or ''Lactobacillus'' from sources other than yeast labs.