Changes

There currently is no formula for how much lactic acid to add to a volume of wort due to the different buffering capacities of wort <ref>[http://www.mbaa.com/districts/Northwest/Events/Documents/Study%20in%20the%20Practical%20Use%20of%20Lactic%20Acid%20Bacteria.pdf A Study in the Practical Use of Lactic Acid Bacteria. Greg Doss from Wyeast Laboratories Inc. 2014.]</ref>. Water chemistry spreadsheets and formulas geared towards mash pH adjustments may not be accurate for wort pH adjustments since wort does not contain grain material, however there has been at least one report reports on MTF that [https://sites.google.com/site/brunwater/ Bru'n Water] can accurately determine how much lactic acid is needed to lower a wort's pH, however this claim requires further investigationor at least provide a starting point. We encourage readers to experiment with water chemistry calculators to see if they can accurate predict wort pH adjustments or get a starting point for how much acid to add <ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1244954842199394/?comment_id=1245053585522853&comment_tracking=%7B%22tn%22%3A%22R%22%7D MTF Thread with Landon Ortiz. 03/03/2016.]</ref><ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1290987234262821/?comment_id=1353870694641141&reply_comment_id=1354548117906732&comment_tracking=%7B%22tn%22%3A%22R9%22%7D Conversation with Adam Boura and Mark Trent on MTF regarding using Bru'n Water for adjusting wort pH. 07/18/2016.]</ref>.

Trial and error is probably the most practical approach at least to some degree. Post boil, the wort pH is generally around 5.0 - 5.2. Adjusting the pH of wort before pitching ''Lactobacillus'' can then be done fairly easily by taking a trial and error approach. Using 1 mL of 88% lactic acid per .1 shift in pH for 5 gallons of wort is a good starting measurement. As an example, say that 5 gallons of wort has a pH of 5.0 just before pitching the ''Lacto''. Begin by adding 5 mL (1 US teaspoon) of food grade lactic acid to the wort for a target of ~4.4 pH. Stir gently, then take another pH reading. Continue to add 1-2 mL of lactic acid until the wort has the desired pH. Derek Springer has observed that it takes about one tablespoon (15 mL) of 88% lactic acid to reach a pH of 4.2 - 4.5 for 5 gallons of wort <ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1290987234262821/?comment_id=1291031577591720&comment_tracking=%7B%22tn%22%3A%22R3%22%7D Conversation with Derek Springer on MTF regarding acidifying wort. 04/24/2016.]</ref>, however a higher amount may be required if the brewer's water is high in bicarbonate (24 mL for 5 gallons of wort to reach a pH of 4.4 was reported by Sean McVeigh for his water which contains 375ppm of bicarbonates <ref>[https://www.facebook.com/groups/MilkTheFunk/permalink/1290987234262821/?comment_id=1291031577591720&reply_comment_id=1291118190916392&comment_tracking=%7B%22tn%22%3A%22R%22%7D Conversation with Sean McVeigh on MTF on acidifying wort. 04/23/2016.]</ref>). Once a pH of 4.0 - 4.4 is reached, pitch the ''Lactobacillus'' culture. This small amount of lactic acid shouldn't have much of an impact on flavor. If a more precise method for determining the required amount of lactic acid is required, a sample of the wort can be pulled and lactic acid or phosphoric acid can be added to it until the target pH is reached, and then that amount can be scaled up (a micropipette might be required to measure very small amounts of lactic/phosphoric acid).