PH Meter

From Milk The Funk Wiki
Revision as of 14:48, 19 May 2015 by DanABA (talk | contribs)
Jump to: navigation, search

A pH Meter is not only considered by some to be an essential tool for all grain homebrewing and commercial brewing, but is also a very useful tool to have for making sour beer. For examples of when an accurate pH reading is useful in the sour brewing process, see the Mixed Fermentation, Sour Worting, and Lactobacillus pages.

Recommend pH Meters

High End pH Meters

Higher end pH meters recommended by our members and others.

Budget pH Meters

pH meters can range from $30 to $500+. The problem with many of the cheaper pH meters is that their reliability and longevity are often questionable [3]. Commonly, two pH meters are recommended by trustworthy sources (AJ Delange and Kai Troester).

Hach Pocket Pro+ pH Tester with Replaceable Sensor.

Hach Pocket Pro+

Features:

  • This pH meter is recommended by AJ Delange [3][4].
  • Does not require storage solution (there is an o-ring seal on the cap, which only needs to have a few drops of distilled water in it).
  • Replaceable sensor.
  • Stability [3].
  • 2 Buffer calibration.
  • Electrode longevity [3].
  • Junction resistant to fouling by sugars, proteins [3].
  • Lets the user decide when to accept a buffer calibration reading [3].
  • ATC [3].
  • Automatic buffer recognition [3].

Disadvantages:

  • Despite having an automatic calibration message, this pH meter still often needs to be calibrated before each brew day [3].

Milwaukee MW102 pH/Temp Meter (updated/upgraded from SM101 and MW101).

Milwaukee MW102

Features:

Disadvantages:

  • This pH meter usually needs to be calibrated before each brew day.
  • Probe replacements appear to be difficult to find. Here is one vendor. eBay has been reported to be another option [8]. Here is a seller that PJ Dunn has had good results from, although he reported slow shipping.

Buffer Solution

Buffer solution will be required to calibrate a pH meter. In general, it is recommended that a pH meter have a 2 point calibration method, which requires 4.0 buffer solution and 7.0 buffer solution. Many buffer solutions for pH meter calibration can be found on Amazon or other retailers. Note that these buffer solutions do have expiration dates, and using expired calibration solutions can throw off pH meter readings.

Testing the Probe

The probes on pH meters generally have a limited life, depending on the quality of the unit. Milwakuee Instruments describes the following method for testing the life of the probe:

"A simple test can be performed using Windex glass cleaner with ammonia and white distilled vinegar. The procedure is as follows: Turn your meter or tester on and place the probe in white distilled vinegar which is acidic (2.4ph) and the reading will be from 2.3 to 2.5 but must be below 3.0 then go to the Windex with ammonia which is alkaline. Your display should move very quickly up the scale to 10.5 – 11.2 but must go above 10.0. If the probe slowly moves up the scale then it is time to consider replacing it. If it does not go below 3.0 pH in vinegar and/or above the 10.0 pH in Windex then probe is dead." [9]

External Articles

References

  1. ↑ Conversation with Jonathan Newman from The Virginia Beer Company on Milk The Funk. 04/19/2015.
  2. ↑ Conversation with Brandon Jones of Embrace The Funk on Milk The Funk. 04/21/2015.
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 AJ Delange. Homebrewtalk Thread. Posted 02/08/2012. Retrieved 04/18/2015.
  4. ↑ Testing the Hach Pocket Pro+ by AJ Delange Homebrewtalk. Retrieved 04/18/2015.
  5. ↑ Kai Troester. Braukeiser. Updated 09/23/2009. Retrieved 04/18/2015.
  6. ↑ Comment by AJ Delange on Homebrewtalk. Posted 08/01/2014. Retrieved 04/18/2015.
  7. ↑ 7.0 7.1 Conversation with Dustin Carver on Milk THe Funk. 4/18/2015.
  8. ↑ Conversation with PJ Dunn on MTF. 05/03/2015.
  9. ↑ Milwaukee Instruments pH General Information Sheet. Retrieved 4/30/2015.
Retrieved from "http://www.milkthefunk.com/w/index.php?title=PH_Meter&oldid=1338"